配置步骤
1、首先升级扩展boot版本，要求boot版本必须为对应版本配套的7.18版本，版本文件中可获取
启动后Ctrl+B进入bootware，选择7进入bootware操作子菜单
选择4设置更新bootware方式通过网线
选择4设置上传配置
设置上传文件名，此处是更新bootware，需上传boot文件;设置IP地址
====================================================
|Note: "." = Clear field. |
| "-" = Go to previous field. |
| Ctrl+D = Quit. |
============================================================================
Protocol (FTP or TFTP) :tftp
Load File Name :wa5300.ipe
:apwa5300_v7.18.btw
Target File Name :wa5300.ipe
:apwa5300_v7.18.btw
Server IP Address :192.168.0.99 10.0.0.233
Local IP Address :192.168.0.98 10.0.0.2
Subnet Mask :255.255.255.0
Gateway IP Address :0.0.0.0
选择1更新bootware
Enter your choice(0-4): 1
Loading...........................Done.
1233920 bytes downloaded!
Updating Basic BootWare? [Y/N]Y
Updating Basic BootWare.....Done.
Updating Extended BootWare? [Y/N]Y
Updating Extended BootWare.........Done.
更新完成后选择0退回主界面并reboot
Enter your choice(0-4): 0
Enter your choice(0-4): 0
重启完成后查看bootwre版本为7.18，再次Ctrl+B进入bootware，Ctrl+F格式化flash，此处注意需要格式化，避免空间不足导致版本解压失败
****************************************************************************
* *
* H3C WA5320 BootWare, Version 7.18 *
* *
****************************************************************************
Copyright (c) 2004-2019 New H3C Technologies Co., Ltd.
Compiled Date : Mar 8 2019
CPU Type : ARM
CPU L1 Cache : 32KB
CPU L2 Cache : 256KB
CPU Clock Speed : 710MHz
Memory Type : DDR3 SDRAM
Memory Size : 256MB
Memory Speed : 533MHz
Flash Size : 32MB
PCB Version : Ver.B
BootWare Validating...
Press Ctrl+B to access EXTENDED-BOOTWARE MENU...
Password recovery capability is enabled.
Note: The current operating device is flash
Enter < Storage Device Operation > to select device.
====================================================
|<1> Boot System |
|<2> Enter Serial SubMenu |
|<3> Enter Ethernet SubMenu |
|<4> File Control |
|<5> Restore to Factory Default Configuration |
|<6> Skip Current System Configuration |
|<7>BootWare Operation Menu |
|<8> Skip Authentication for Console Login |
|<9> Storage Device Operation |
|<0> Reboot |
============================================================================
Ctrl+Z: Access EXTENDED ASSISTANT MENU
Ctrl+F: Format File System
Ctrl+C: Display Copyright
Ctrl+Y: Change AP Mode
Enter your choice(0-9):
Warning:All files on flash will be lost! Are you sure to format? [Y/N]Y.....
............................................................................
..................
Format success.
格式化完成后选择3进入ethernet子菜单
====================================================
|<1> Boot System |
|<2> Enter Serial SubMenu |
|<3> Enter Ethernet SubMenu |
|<4> File Control |
|<5> Restore to Factory Default Configuration |
|<6> Skip Current System Configuration |
|<7>BootWare Operation Menu |
|<8> Skip Authentication for Console Login |
|<9> Storage Device Operation |
|<0> Reboot |
============================================================================
Ctrl+Z: Access EXTENDED ASSISTANT MENU
Ctrl+F: Format File System
Ctrl+C: Display Copyright
Ctrl+Y: Change AP Mode
Enter your choice(0-9): 3
选5设置有线网络配置，上传之前需要把胖AP版本文件名改成wa5300-oasis.ipe
====================================================
|Note:the operating device is flash |
|<1> Download Image Program To SDRAM And Run |
|<2> Update Main Image File |
|<3> Update Backup Image File |
|<4> Download Files(*.*) |
|<5> Modify Ethernet Parameter |
|<0> Exit To Main Menu |
| |
============================================================================
Enter your choice(0-5): 5
====================================================
|Note: "." = Clear field. |
| "-" = Go to previous field. |
| Ctrl+D = Quit. |
============================================================================
Protocol (FTP or TFTP) :tftp
Load File Name :apwa5300_v7.18.btw
:wa5300-oasis.ipe
Target File Name :apwa5300_v7.18.btw
:wa5300-oasis.ipe
Server IP Address :10.0.0.233
Local IP Address :10.0.0.2
Subnet Mask :255.255.255.0
Gateway IP Address :0.0.0.0
配置完成后选择2，更新主版本文件
====================================================
|Note:the operating device is flash |
|<1> Download Image Program To SDRAM And Run |
|<2> Update Main Image File |
|<3> Update Backup Image File |
|<4> Download Files(*.*) |
|<5> Modify Ethernet Parameter |
|<0> Exit To Main Menu |
| |
============================================================================
Enter your choice(0-5): 2
Loading.....................................................................
............................................................................
............................................................................
............................................................................
............................................................................
............................................................................
............................................................................
..............Done.
27445248 bytes downloaded!
Image file wa5300-oasis-boot.bin is self-decompressing...
Saving file flash:/wa5300-oasis-boot.bin ...................................
.............................Done.
Image file wa5300-oasis-system.bin is self-decompressing...
Saving file flash:/wa5300-oasis-system.bin .................................
............................................................................
............................................................................
............................................................................
............................................................................
...........................Done.
升级完成后选择0退回主界面并且reboot
====================================================
|Note:the operating device is flash |
|<1> Download Image Program To SDRAM And Run |
|<2> Update Main Image File |
|<3> Update Backup Image File |
|<4> Download Files(*.*) |
|<5> Modify Ethernet Parameter |
|<0> Exit To Main Menu |
| |
============================================================================
Enter your choice(0-5): 0
====================================================
|<1> Boot System |
|<2> Enter Serial SubMenu |
|<3> Enter Ethernet SubMenu |
|<4> File Control |
|<5> Restore to Factory Default Configuration |
|<6> Skip Current System Configuration |
|<7>BootWare Operation Menu |
|<8> Skip Authentication for Console Login |
|<9> Storage Device Operation |
|<0> Reboot |
============================================================================
Ctrl+Z: Access EXTENDED ASSISTANT MENU
Ctrl+F: Format File System
Ctrl+C: Display Copyright
Ctrl+Y: Change AP Mode
Enter your choice(0-9): 0
System is starting...
Press Ctrl+D to access BASIC-BOOTWARE MENU
Booting Normal Extended BootWare
The Extended BootWare is self-decompressing.................................
.Done.
****************************************************************************
* *
* H3C WA5320 BootWare, Version 7.18 *
* *
****************************************************************************
Copyright (c) 2004-2019 New H3C Technologies Co., Ltd.
Compiled Date : Mar 8 2019
CPU Type : ARM
CPU L1 Cache : 32KB
CPU L2 Cache : 256KB
CPU Clock Speed : 710MHz
Memory Type : DDR3 SDRAM
Memory Size : 256MB
Memory Speed : 533MHz
Flash Size : 32MB
PCB Version : Ver.B
BootWare Validating...
Press Ctrl+B to access EXTENDED-BOOTWARE MENU...
Loading the main image files...
Loading file flash:/wa5300-oasis-system.bin.................................
............................................................................
...........................................................................
Done.
Loading file flash:/wa5300-oasis-boot.bin...................................
Done.
Image file flash:/wa5300-oasis-boot.bin is self-decompressing...............
............................................................................
............................................................................
............................................................................
............................................................................
...............................Done.
System image is starting...
Startup configuration file doesn"t exist or is invalid.
Line con0 is available.
Press ENTER to get started.
至此设备启动完成
配置关键点
1.需要升级设备bootware版本至7.18
2.升级完bootware后需要格式化Flash
3.对应版本文件需要修改成wa5300-oasis.ipe
云AP是Fat AP。初次使用云AP，给云AP上电后，云AP会默认开启4个无线服务：
l 其中一个称之为管理WIFI，也称内部WIFI，SSID为H3C_XXXXXX，XXXXXX为设备mac地址后六位。管理WIFI供商铺内部员工管理使用，一般在2.4G频段工作，当设备未连接到绿洲时，通过连接管理WIFI在浏览器输入10.40.94.1或myap.h3c.com访问本地web页面可进行本设备下的无线服务管理配置，一旦连接上绿洲，将只能通过绿洲平台进行统一的无线服务配置管理。
其余3个称为用户WIFI，也称商业WIFI，SSID为H3C_WiFi_1、H3C_WiFi_2、H3C_WiFi_3，不加密，不认证，不隐藏。当设备连接到外网，可为已经连接上用户WIFI的用户提供上网服务。